01. Identify the command to display the IP routing table?
A.) Show route B.) Show ip route
C.) Show ip table route D.) Show ipx route
02. Identify the command to display all the valid commands at the given mode?
A.) Help all B.) Help
C.) All commands D.) ?
03. Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K B.) Crtl-C
C.) Ctrl-Z D.) Crtl-End
04. Identify the command to display the configured IP routing protocols?
A.) Show protocols B.) Show protocols all
C.) Show routing-protocols D.) Show ip protocols
05. Identify the command to configure ALL the default VTY ports?
A.) Router (config)# line vty 0 4 B.) Router# line vty 0 4
C.) Router (config)# line vty D.) Router (config)# line vty 0
06. Identify the command to reload the router?
A.) Router (config)# reload B.) Router# reset
C.) Router# reload D.) Router> reload
07. Identify command that configures 'Cisco1' as a secret password?
A.) Router (config)# enable secret password Cisco1 B.)Router (config)# enable secret cisco1
C.) Router (config)# enable password Cisco1 D.)Router (config)# enable secret Cisco1
08. Identify the command that displays ethernet0/1 interface status?
A.) Show interface ethernet0/1 B.) Show interface ethernet e0/1
C.) Show interface ethernet0.1 D.) Show ethernet0/1
09. Identify the command that saves the configuration stored in RAM to NVRAM?
A.) Copy running-config startup-config B.) Copy tftp running-config
C.) Copy startup running D.) Copy active to backup
10. Identify the command to configure the IP address 172.16.100.5 255.255.255.0?
A.) Router (config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router (config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router (config)# ip address 172.16.100.5 255.255.255.0
11. Identify the command to display the hardware platform information?
A.) Show all B.) Show platform
C.) Display hardware D.) Show version
12. Given the command 'cal?’ what will it display?
A.) Syntax of the 'clock' command B.) Syntax of the 'clear' command
C.) All commands that begin with 'cal' D.) All commands that begin with 'c'
13. Identify the 2 commands the saves the running-config to NVRAM?
A.) Write memory B.) Copy running-config startup-config
C.) Write network D.) Write backup
14. Identify the command to determine if CDP is enabled?
A.) Show enable cap B.) Show cap enabled
C.) Show cap run D.) Show cap
15. Which 2 commands show the Cisco IOS filename?
A.) Show IOS B.) Show ver
C.) Show flash D.) Show memo
E.) Show NVRAM
16. Identify the command to copy a configuration file from a TFTP server to a routers active configuration?
A.) Router# copy running-config tftp B.) Router# copy tftp running-config
C.) Router# copy tftp 172.16.0.1 running-config D.) Router (config)# copy tftp running-config
17. Identify the command to configure the router for IGRP autonomous system 100?
A.) Router (config)# router igrp 100 B.) Router> router igrp 100
C.) Router# router igrp 100 D.) Router (config)# router igrp
18. Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102 B.) Router (config)# config-register 0x2102
C.) Router (config-reg)# 0x2102 D.) Router> config-register 0x2102
19. Identify the command to disable CDP on an interface?
A.) Router (config-if)# no cdp enable B.) Router (config-if)# no cdp run
C.) Router# no cdp enable D.) Router (config-if)# no cdp
20. Identify the command that will display the RIP routes entering and leaving the router?
A.) Router (config)# debug ip rip B.) Route# debug ip rip
C.) Router>debug ip rip D.) Router# debug rip routes
21. Identify the prompt displayed if in privileged exec mode?
A.) Router (config)# B.) Router#
C.) Router> D.) Router (priv)#
52. What is the command to copy the IOS image to a TFTP server?
A.) Copy flash tftp B.) Copy running-config tftp
C.) Copy ios tftp D.) Copy startup-config tftp
22. Identify the keystroke to position the cursor to the beginning of a command line?
A.) Ctrl-A B.) Ctrl-Ins
C.) Ctrl-B D.) Ctrl-Z
23. You have a Class B network address divided into 30 subnets. You will add 25 new subnets within the next year. You need 600 host IDs for each subnet. Which subnet mask should you use?
24 A.) 255.254.0.0 B.) 255.192.0.0
C.) 255.255.252.0 D.) 255.255.248 0
25. Which command allows a user to see previous commands?
A.) show command B.) CTRL-P
C.) show history D.) CTRL-U
E.) Up Arrow F.) SHIFT-CTRL-6
No comments:
Post a Comment